LOAD SUSTAINED RIG FOR BOND DURABILITY STUDY

Authors

  • Shukur Abu Hassan Department of Structure and Materials, Faculty of Civil Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor, MALAYSIA
  • Yob Saed Ismail Department of Structure and Materials, Faculty of Civil Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor MALAYSIA
  • Abd Rahman Mohd. Sam Department of Structure and Materials, Faculty of Civil Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor, MALAYSIA

Keywords:

Bond durability, CFRP plate-concrete bonded system, experimental rig, load sustainable

Abstract

This paper describes the development of a special-built experimental rig used for bond durability study of composites specimen under combination of sustainable mechanical load and weathering effects. The specimen under study was Carbon Fibre-Reinforced Plastic (CFRP) plates bonded with special structural epoxy adhesive to a concrete prism. The fully mechanical rig was designed to create and sustain pull-push load configuration to the specimen. From setting-up process, laboratory monitoring works and CFRP plate strain data, it shows that the rig performed well without any maintenance throughout the period.

References

Macdonald, M. D., and Calder, A. J. J., 1982. Bonded Steel Plating for Strengthening Concrete Structures, International Journal of Adhesion and Adhesive, Vol. 2, No. 2, pp. 119-127.

Swamy R.N., Jones R, and Charif A., 1986. Shear Adhesion Properties of Epoxy Resin Adhesives, Proceedings of International Symposium on Adhesion Between Polymers and Concrete, pp. 741-755.

Calder, A.J.J., 1979. Exposure Tests on Externally Reinforced Concrete Beams – First Two Years. Transport and Road Research Laboratory, Supplementary Report 529, Berkshire, UK: Crowthrone.

Calder, A.J.J., 1982 The Microstructure of Epoxy Bonded Steel-to-Concrete Joints. Transport and Road Research Laboratory, Supplementary Report 705, Berkshire, UK: Crowthrone.

Calder, A.J.J.,1988 Exposure Tests on Externally Reinforced Concrete Beams–Performance after 10 Years. Transport and Road Research Laboratory, Supplementary Report 129, Berkshire, UK: Crowthrone.

Calder, A.J.J.,1989 Exposure Tests on 3.5m Externally Reinforced Concrete Beams The First 8 Years, Transport and Road Research Laboratory, Supplementary Report191, Berkshire, UK: Crowthrone.

Calder, A.J.J.,1990 Durability of Steel Plates Bonded to Concrete with Structural Epoxy Adhesive International Seminar on Structural Repairs Strengthening by the Plate Bonding Technique, University of Sheffield, SIRIUS.

Swamy, R.N, Hobbs, B. and Roberts, M.,1995 Structural Behaviour of Externally Bonded Steel Plated RC Beams after Long-Term Exposure. Structural Engineer, pp. 255-261.

Nakaba, K, Kanakubo, T., Furuta T. and Yoshizawa H.,2001. Bond Behaviour between Fibre-Reinforced Polymer Laminates and Concrete. ACI Structural Journal, pp. 359-367.

Mukhopadhyaya, P, Swamy, R.N., and Lynsdale C.J.,1998 Influence of Aggressive Exposure Conditions on the Behaviour of Adhesive Bonded Concrete – GFRP Joints, Journal of Construction and Building Materials 12, pp. 427-446.

Maeda T., Asano Y., Sato Y., Ueda T. and Kakuta Y.,1997 A Study on Bond Mechanism of Carbon Fiber Sheet, Non-Metallic (FRP) Reinforcement for Concrete Structure, Proceeding of the Third International Symposium, Vol.1, pp. 279-286.

Brosens, K and Van Gemert, D., 1997 Anchoring Stresses Between Concrete and Carbon Fibre Reinforced Laminates, Non-Metallic (FRP) Reinforcement for Concrete Structures, Proceeding for Third International Symposium, Vol. 1, pp. 271-278.

Horiguchi, T. and Saeki, N.,1997 The Effect of Test Methods and Quality of Concrete on Bond Strength of CFRP Sheet, Proceeding of Non-metallic FRP Reinforcement for Concrete Structure, pp. 265-274.

Toutanji, H. and Ortiz, G.,2001 The Effect of Surface Preparation on the Bond Interface between FRP Sheets and Concrete Members, Journal of Composite Structures, pp. 457-462.

Abdul Rahman M. S. and Shukur, A. H. 2005 Fibre Reinforced Polymer Composites in Constructionâ€, National Civil Engineering Conference 2005 (NACEC2005), KUITTHO, Johor.

Hodgkinson, J.M. Mechanical Testing of Advanced Fibre Composites. Woodhead Publishing Limited, Cambridge England, 2000 pp. 121.

Shukur, A. H., Abdul Rahman, M. S. and Yob, S.I. 2002 Tensile Behaviour of CFRP and GFRP Reinforcements. Research Seminar on Materials and Construction, UTM, Malaysia.

Hojo, M., Sawada, Y. and Miyairi, H, 1994 Influence of Clamping Method on Tensile Properties of Unidirectional CFRP in 0º and 90º Directions – Round Robin Activity for International Standardization in Japan, Journal of Composites, Vol. 8, No. 1-4.

Shukur, A.H., Abdul Rahman, M. S. and Yob Saed, I., 2003 Bond Behaviour of CRFP Plate Bonded of Concrete. Malaysia Science and Technology Congress.

Shukur, A. H., 2007 Mechanical Performance of Carbon Fibre Reinforced Vinyl Ester Composite Plate Bonded Concrete Exposed to Tropical Climate, PhD Thesis, UTM.

Shigley, J.E., Mischke, C.R. and Budynas, R.G., 2003 Mechanical Engineering Design. 7th edition, pp. 24.

Juvinall, R.C. and Marshek, K.M., 1991 Fundamental of Machine Components Design. Second Edition, John Wiley & Sons, pp. 190.

Swanson, R.S.,1997 Introduction to Design and Analysis with Advanced Composite Material. Prentice-Hall International, Inc.

Clarke John L., 1996 Structural Design of Polymer Composites: Eurocomp Design Code and Handbook, E and Spon.

Tokyo Sokki Kenkyujo Co., Ltd: 2003 TML Strain Gauge Test Data. Tokyo, Japan.

Downloads

Published

2018-04-04

How to Cite

Abu Hassan, S., Ismail, Y. S., & Mohd. Sam, A. R. (2018). LOAD SUSTAINED RIG FOR BOND DURABILITY STUDY. Jurnal Mekanikal, 28(1). Retrieved from https://jurnalmekanikal.utm.my/index.php/jurnalmekanikal/article/view/122

Issue

Section

Mechanical

Similar Articles

<< < 2 3 4 5 6 7 8 9 10 11 > >> 

You may also start an advanced similarity search for this article.