NUMERICAL INVESTIGATION OF THE FLOW INSIDE PRIMARY ZONE OF TUBULAR COMBUSTOR MODEL

Authors

  • Yehia A. Eldrainy Aeronautical Engineering Department Faculty of Mechanical Engineering Universiti Teknologi Malaysia 81310 Johor Bahru, Johor
  • Mohammad Nazri Mohd Jaafar Aeronautical Engineering Department Faculty of Mechanical Engineering Universiti Teknologi Malaysia Johor Bahru, Johor
  • Tholudin Mat Lazim Aeronautical Engineering Department Faculty of Mechanical Engineering Universiti Teknologi Malaysia 81310 Johor Bahru, Johor

Keywords:

Isothermal flow, numerical simulation, tubular combustor, turbulence, air swirler

Abstract

In this study, a numerical simulation of non-reacting flow inside a gas turbine combustor model was performed. The main target of this investigation is to get physical insight of the main vortex, responsible for the efficient mixing of fuel and air. Such models are necessary for developing and optimization of real combustors. Combustor swirler assists the fuel-air mixing process by producing recirculation region which can act as flame holders as well. Therefore, proper selection of a swirler is needed to stabilize the flame, to enhance combustor performance and to reduce NOx emissions. For that reason, several axial swirlers with different configurations were employed to show their effects on primary zone aerodynamics performance. The three-dimensional, steady, turbulent and isothermal flow inside the combustor model was simulated using a finite volume based CFD code FLUENT 6.2. The combustor model geometry was created by means of solid model CAD software then the meshing was generated using GAMBIT preprocessing software subsequently, and the solution and the results analysis were carried out in a FLUENT solver. The effects of different swirlers’ configurations and inlet mass flow rate on flow dynamics were examined. A two recirculation zones were predicted, the first one is a central recirculation and located in the region immediately downstream of the swirler and the second is corner recirculation and located in the upstream corner of the combustion chamber. The results show that swirlers’ configuration and inlet mass flow rate have a significant effect on the combustor flowfield and pressure losses. By the mean that as swirl number increases the central recirculation zone size, turbulence production and pressure loss increase.

References

Lefebvre, A.H., 1983. Gas turbine combustion, McGraw-Hill series.

Correa, S.M., 1993. A Review of NOX Formation under Gas-Turbine Combustion Conditions, Combustion Science and Technology, Vol.87, 329-362.

Mellor, M., 1990. Design of Modern Gas Turbine Combustors, Academic Press.

Philip, P. Walsh and Fletcher, P., 2005. Gas Turbine Performance, Blackwell Science.

Wang, Y., Yang, V. and Yetter, R.A., 2004. Numerical Study on Swirling Flow in an Cylindrical Chamber, 42nd AIAA Aerospace Sciences Meeting, Reno, Nevada.

Karvinen and Ahlstedt, H., 2005. Comparison of Turbulence Models in Case of Jet in Cross Flow Using Commercial CFD Code, Engineering Turbulence Modeling and Experiments 6, Elsevier Ltd.

Menzies, K.R., 2005. An Evaluation of Turbulence Models for The Isothermal Flow in A Gas Turbine Combustion System, In 6th International Symposium on Engineering Turbulence Modeling and Experiments, Sardinia, Italy.

Palma, J.M.L.M., 1988. Mixing in Non-Reacting Gas Turbine Combustor Flows, Ph.D Thesis, University of London, UK.

Hsiao, G. and Mongia, H., 2003. Swirl Cup Modeling Part III: Grid Independent Solution with Different Turbulence Models, AIAA.

Launder, B.N. and Spalding, D.B., 1972. Lectures in Mathematical Models of Turbulence, Academic Press, London, England.

Lin, S. and Griffiths, A.J., 1995. CFD simulation of cooling air flows within shrouded finned heater/cooler systems used on barrel extruders, Proceedings of the Joint ASME/JSME Fluid Engineering Annual Conference, USA.

FLUENT 6.2 User's Guide, Fluent Inc. 2005.

Versteeg, H.K. and Malalasekera, W., 1995. An Introduction to Computational Fluid Dynamics, the Finite Volume Method, Longman Group Ltd.

Downloads

Published

2018-04-09

How to Cite

A. Eldrainy, Y., Mohd Jaafar, M. N., & Mat Lazim, T. (2018). NUMERICAL INVESTIGATION OF THE FLOW INSIDE PRIMARY ZONE OF TUBULAR COMBUSTOR MODEL. Jurnal Mekanikal, 26(2). Retrieved from https://jurnalmekanikal.utm.my/index.php/jurnalmekanikal/article/view/148

Similar Articles

<< < 1 2 3 4 5 6 7 8 9 10 > >> 

You may also start an advanced similarity search for this article.