MULTI CHARACTERISTIC OPTIMIZATION OF FLUX CORED ARC WELDING PROCESS PARAMETERS USING GREY BASED GAAPPROACH

Authors

  • P. SREERA P. SREERA Department of Mechanical Engineering Younus College of Engineering and Technology Kerala, India-691010

Keywords:

Flux cored arc welding, analysis of variance, taguchi method, grey based genetic algorithm

Abstract

This paper presents the application of Taguchi method coupled with grey based GA approach for multiple output optimization of flux cored arc welding (FCAW) to obtain optimal weld bead geometry in mild steel plates IS 2062.This approach converts complex multiple objectives into a single grey reasoning grade which is the objective function for genetic algorithm (GA) approach. The welding parameters such as voltage, current, stick out and wire feed are optimized with multiple considerations such as bead width, penetration, reinforcement and dilution. Taguchi’s concepts of orthogonal array signal to noise (S/N) ratio has been used to optimize FCAW through a single comprehensive output measure (COM) which is the objective function. The significant contributions of parameters are estimated using analysis of variance (ANOVA) test. Confirmation test is conducted and reported. It is found that welding current is the most significant factor affecting bead geometry. Results indicate feasibility of grey based GA analysis in continuous improvement of welding industry.

References

Kannan.T. and Murugan, N., 2006. Effect of flux cored arc welding process parameters on duplex stainless steel clad quality. Journal of Material Processing

Technology, 176, 230-239.

Kannan,T. and Murugan, N., 2006.Prediction of ferrite number of duplex stainless steel clad metals using RSM, Welding Journal, 91-99.

Gunaraj,V. and Murugan, N., 2005. Prediction and control of weld bead geometry and shape relationships in submerged arc welding of pipes, Journal of Material Processing Technology, 168, 478-487.

Kim, I.S., Son, K.J., Yang, Y. S. and Yaragada, P. K.D.V., 2003. Sensitivity analysis for process parameters in GMA welding process using factorial design method, International Journal of Machine Tools and Manufacture, 43, 763-769.

Jagannatha, N., Hiremath, S.S. and Sadashivappa, K., 2012. Analysis and parametric optimization of abrasive hot air jet machining for glass using Taguchi method and utility concept, International Journal of Mechanical and Materials Engineering, 7, 9-15.

Muhammed N., Manurung, Y.H.P. and Muhammed Hafidzi, 2012. Optimization and modelling of spot welding parameters with simultaneous response consideration using multi objective Taguchi method and utility concept, Journal

of Mechanical Science and Technology, 26 (8), 2365-2370.

Gautam Nandi, Saurav Datta, Ashish Banyopadhay and Pradip Kumar Pal, 2010. Analysis of hybrid Taguchi methods for optimization of submerged arc weld, Proceeding of Joining Process: Challenges for Quality, Design and Development,

NIT, Agrathala, India, March 5-6, 2010.

Tarng,Y.S. and Yang, W.H., 1998. Optimization of weld bead geometry in gas tungsten arc welding by the Taguchi method, International Journal of Advanced Manufacturing Technology. 14, 549-554.

Saurav Datta, Ashish Banyopadhay and Pradip Kumar Pal, 2008. Grey based Taguchi method for optimization of bead geometry in submerged arc bead on plate welding, International Journal of Advanced Manufacturing Technology, 39, 1136-1143.

Downloads

Published

2018-04-01

How to Cite

P. SREERA, P. S. (2018). MULTI CHARACTERISTIC OPTIMIZATION OF FLUX CORED ARC WELDING PROCESS PARAMETERS USING GREY BASED GAAPPROACH. Jurnal Mekanikal, 38(2). Retrieved from https://jurnalmekanikal.utm.my/index.php/jurnalmekanikal/article/view/20

Issue

Section

Mechanical

Similar Articles

<< < 2 3 4 5 6 7 8 9 10 11 > >> 

You may also start an advanced similarity search for this article.