EFFECT OF WIRE-EDM CUTTING ON FATIGUE STRENGTH OF AZ61 MAGNESIUM ALLOY
Keywords:
Wire-EDM, cutting pit, stress intensity factor, fatigue, magnesium alloyAbstract
Effect of wire electrical discharge machining (wire-EDM) cutting on fatigue strength of an extruded AZ61 magnesium alloy at room temperature was investigated. The surface condition of the samples after the wire-EDM cutting process is compared to the samples which have undergone careful polishing on their surfaces. A series of high cycle fatigue tests are performed on both the wireEDM as-cut and polished samples with constant amplitude stress at the frequency of 10 Hz. Fractographic analyses were conducted on the tested samples to identify the mechanism of fatigue fracture. The finding show that the fatigue limit of wireEDM as-cut specimen is 20 MPa lower as compared to smoothly polished specimens. Fatigue cracks are found to initiate and propagate to final failure from a cutting pit on the wire-EDM as-cut specimens.References
Duffy, L., 1996, Magnesium Alloys: The Light Choice for Aerospace, Materials World: 127-130.
Mordike, B.L. and Ebert, T., 2001, Magnesium: Properties-ApplicationPotential, Material Science Engineering, A302: 37-45.
Umehara, T., Sajuri, Z., Miyashita, Y. and Mutoh, Y., 2002, Effect of surface roughness on fatigue behaviour of magnesium alloy. Proceeding of 103rd of Japan Institution of Light Metal, 59-60.
Yerokhin, A. L. Shatron, A., Samsonov, V. and Shashkov P., 2004, Fatigue properties of Keronite coating on a magnesium alloy, Surface and Coating Technology, 182: 78-84.
Cole, G.S. and Sherman, A.M., 1995, Materials Characterizations, 35: 3-9.
Russel-Stevens, Todd R. and Papakyriacou, M., 2005, The Effect of Thermal Cycling on Properties of a Carbon Fiber Reinforced Magnesium Composite. Material Science Engineering, A397: 249-257.
Srivatsan, T.S., Meslet Al-Hajri and Lam, P.C., 2005, The Quasi-Static, Cyclic Fatigue and Final Fracture Behavior of Magnesium Alloy MetalMatric Composite, Composite: Part B 36: 209-222.
Kalpakjian, S. and Steven, R., 2000, Manufacturing Engineering and Technology, 4th edition, Prentice Hall: 757-759.
Arola, D. and William, C. L., 2002, Estimating the fatigue stress
concentration factor of machined surface effect of surface, International Journal of Fatigue, 24: 923-930.
Jeelani, S. and Collins M.R., 1988, Effect of electric discharge machining on the fatigue life of Inconel 718, International Journal Fatigue, 10: 121-125.
Ramulu, M. and Paul, G. L., 2001, EDM surface effects on the fatigue strength of a 15 vol% SiC/Al metal matrix composite, International Journal of Composite Structures, 54: 79-86.
Kusukawa, K. and Takao, K., 2002, Fatigue Crack Initiation Behavior and Notch Sensivity of AZ92A magnesium alloy, Journal Japan Society of Mechanical Engineer, 94-99.
Khan, A., Ahsan Munira, M. A. and Norhasimah M. S., 2006, Relationship of surface roughness with current and voltage during wire EDM, Journal of Applied Sciences, 6(10): 2317-2320.
Singh, H. and Gary, R. 2009. Journal of Achievement in Materials and Manufacturing, 32: 70-74.
Newman, J.C. and Raju, I.S., 1986. ASTM Special Technical Publication, 789-795.
Sajuri, Z., Umehara, T., Miyashita, Y. and Mutoh Y., 2003: Fatigue-Life Prediction of Magnesium Alloys for Structural Applications. Advanced Engineering Materials, 5(12): 910-916.
Downloads
Published
How to Cite
Issue
Section
License
Copyright of articles that appear in Jurnal Mekanikal belongs exclusively to Penerbit Universiti Teknologi Malaysia (Penerbit UTM Press). This copyright covers the rights to reproduce the article, including reprints, electronic reproductions or any other reproductions of similar nature.