PERFORMANCE EVALUATION ON DRILLING OF AUSTENITIC STAINLESS STEEL 316L USING HSS TOOL

Authors

  • Mohamad Sharidan Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor
  • Safian Sharif Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor

Keywords:

Drilling, Tool wear, Surface roughness, Dimensional accuracy, Roundness

Abstract

This paper presents the effect of drilling parameters on tool wear, tool life, surface roughness, dimensional accuracy and roundness when drilling austenitic stainless steel 316L using HSS tool. Experimental trials were conducted at different cutting speeds of 10, 16 and 22 m/min with constant feed rates of 0.05 and 0.075 mm/rev and under dry and coolant conditions. Results showed that the number of drilled holes was significantly influenced by the cutting speed whereby increasing cutting speed decreases the number of holes. Surface roughness measurement showed that better surface finish was obtained at lower cutting speed and feed rate. Results also showed that the dimensional accuracy at lower feed rate is better than at higher feed rate. From the roundness aspect, it was found that the new tool contribute to the good roundness compared to the worn tool.

References

Rajender Singh, (2006). Introduction to Basic Manufacturing Processes and Workshop Technology.New Age International (P) Ltd.

Seagle, S.R. and Wood, J.R. (1993). Advances in Titanium Alloys.Key Engineering Materials.Vol 77-78 pg 91-102.

Lee Joo Hong, (2005). Drilling of Titanium Alloy Ti-6Al-4V using Uncoated and Coated Carbide Drills – Surface Integrity Study.Faculty of Mechanical Engineering, UniversitiTeknologi Malaysia

Ahmad Afzanbin Ahmad Alwi, (2008). Drilling of Stainless Steel AISI 630 H1075 using Different Type of TiAlN Carbide Drill. Faculty of Mechanical Engineering, UniversitiTeknologi Malaysia

Ali Akhavan Farid, (2008). Surface Integrity of Inconel 718 during Drilling Operation.Faculty of Mechanical Engineering, Universiti Teknologi Malaysia

Asmar Suid, (2010). Investigation on Microscopic Behavior of Austenitic Steel Plates During Holes Piercing Process. Faculty of Mechanical Engineering, Universiti Teknologi Malaysia

Hasrul Shafiq Kamaruzaman, (2011). Surface Integrity Study when drilling Inconel 718 using Coated Carbide Tool, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia

http://en.wikipedia.org/wiki/Stainless steel

Jinsoo Kim, (2002), Development of an Analytical Model for Drilling Burr Formation in Ductile Materials, ASME.Vol 124, April 2002

http://catalogs.indiamart.com/products/hss-drill-bits.html

Dornfield D.A., Kim J.S., Dechow H., Hewson J. and Chen L.J., (1999). Drilling Burr Formation in Titanium Alloy, Ti-6Al-4V.Annals of the CIRP. Vol. 48/1/1999

http://www.interlloy.com.au/our-products/stainless-steel/316l-austenitic-stainless-steel-bar/

Ko S. L., Chang J. E. (2003), Development of Drill Geometry for Burr Minimization in Drilling, Annals of the CIRP. Vol. 52/1/2003

Sharif S. and Rahim E. A. (2007), Performance of coated- and uncoated-carbide tools when drilling titanium alloy-Ti6A14V, Journal of Materials Processing technology 185, pp. 72-76.

Bono M. and Hi J., The effects of thermal distortions on the diameter and cylindricity of dry drilled holes, International Journal of Machine Tools and Manufacture 41 (2001) 2261-2270.

Bruce J. Black, (2004), Third Edition, Workshop Processes, Practices and Materials.Gwent College of Higher Education, Newgen Imaging Systems (P) Ltd., Chennai, India

Azlan Abdul Rahman, Azuddin Mamat and Abdullah Wagiman (2009), Effect of Machining Parameters on Hole Quality of Micro Drilling for Brass, Journal of Modern Applied Science, 5, pp. 221-230

Erween Abd Rahim (2005). Performance Evaluation of Uncoated and Coated Carbide tools when Drilling Titanium Alloy.Faculty of Mechanical Engineering, UniversitiTeknologi Malaysia

Naife A. Talib, (2010), Studying the Effect of Cutting Speed and Feed Rate on Tool Life in the Turning Processes. First Engineering Scientific/Conference College of Engineering-University of Diyala, 22-23 Dec. 2010, pp. 181-194

http://en.wikipedia.org/wiki/Drill_bit

Downloads

Published

2018-04-01

How to Cite

Sharidan, M., & Sharif, S. (2018). PERFORMANCE EVALUATION ON DRILLING OF AUSTENITIC STAINLESS STEEL 316L USING HSS TOOL. Jurnal Mekanikal, 37(2). Retrieved from https://jurnalmekanikal.utm.my/index.php/jurnalmekanikal/article/view/38

Issue

Section

Mechanical

Similar Articles

<< < 1 2 3 4 5 6 7 8 9 10 > >> 

You may also start an advanced similarity search for this article.