PERFORMANCE EVALUATION OF WIRE ELECTRO DISCHARGE MACHINING ON SILICON CARBIDE

Authors

  • Mohd Yazid Abu Faculty of Mechanical Engineering Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia
  • Hamidon Musa Faculty of Mechanical Engineering Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor, Malaysia

Keywords:

wire electro discharge machining, reaction-bonded silicon carbide, pulse on, pulse off, peak current, servo voltage, surface roughness, sparking gap, cutting speed, design of experiment

Abstract

The machining of reaction-bonded silicon carbide (RBSiC) using wire electro-discharge machining (WEDM) with brass wire diameter of 0.25 mm has been used as the tool electrode. The main purpose of this study was to investigate the influenced of various parameters involved namely pulse on (ON), pulse off (OFF), peak current (IP) and servo voltage (SV) on the machining characteristics, namely surface roughness (Ra), sparking gap (Gap) and cutting speed (CS). The Full Factorial Design of Experiment (DOE) approach with two-level was used to formulate the experimental layout, to analyze the effect of each parameter on the machining characteristics and to predict the optimal setting for each WEDM parameters. Confirmation tests were also conducted for the optimum conditions for each machining characteristics in order to verify and compare the results from the theoretical prediction using Design Expert software and experimental confirmation tests. In general, results revealed that pulse on and peak current have appeared to be the significant effect to all responses investigated. Overall, the results from the confirmation tests showed that the percentage of performance was acceptable due to all the results obtained were within the allowable values which was less than 15% of margin error.

References

H. Ramasamy and L. Blunt. (2004). â€Effect of EDM Process Parameters on 3D Surface Topology.†Journal of Materials Processing Technology. 148: pp. 155-164.

Ho, K.H., Newman, S.T., Rahimifard, S. and Allen, R.D. (2004). â€State of the Art in Wire Electrical Discharge Machining (WEDM).†International Journal of Machine Tools & Manufacture. 44: pp. 1247-1259.

M.S. Hewedy, T.A. El-Taweel, and M.F. El-Safty. (2005). “Modeling The Machining Parameters of Wire Electro Discharge Machining of Inconel 601 using RSM.†Journal of Material Processing Technology. 169: pp. 328-336.

Martin R. Metzger and Mark L. Witmer. (2000). “Understanding Silicon Carbide Types Having The Right Tool for the Jobâ€. World Coal Magazine. Inc. Silicon Carbide Products.

Lochner, R.H. and Matar, J.E. (1990). “Designing for Quality: An Introduction to the Best of Taguchi and Western Methods of Statistical Experiment Design.†Chapman and Hall, New York.

Montgomery (2001). “Practical Experiment Design for Engineers and Scientist.†3rd Edition, John Waley & sons, Inc. New York.

K. M. Patel, Pulak M. Pandey, and P. Venkateswara Rao. (2009). “Determination of an Optimum Parametric Combination Using a Surface Roughness Prediction Model for EDM of Al2O3/SiCw/TiC Ceramic Composite†Journal of Materials and

Manufacturing Processes. 2009.

Mas Ayu. H. (2006). “Performance Evaluation of WEDM on Tungsten Carbide.†Master Project Report Universiti Teknologi Malaysia, Skudai.

Lee, S.H. and Li, X.P. (2001). “Study of the Effect of Machining Parameters on the Machining Characteristics in Electrical Discharge Machining of Tungsten Carbide.†Journal of Materials Processing Technology. 115: pg. 344-358.

Downloads

Published

2018-04-02

How to Cite

Abu, M. Y., & Musa, H. (2018). PERFORMANCE EVALUATION OF WIRE ELECTRO DISCHARGE MACHINING ON SILICON CARBIDE. Jurnal Mekanikal, 36(1). Retrieved from https://jurnalmekanikal.utm.my/index.php/jurnalmekanikal/article/view/62

Issue

Section

Mechanical

Similar Articles

<< < 12 13 14 15 16 17 18 19 20 21 > >> 

You may also start an advanced similarity search for this article.