EFFECT OF SINGLE OVERLOAD ON STRESS DISTRIBUTION IN AN AXIALLY LOADED 2024-T351 ALUMINIUM ALLOY PLATE SPECIMEN WITH A HOLE

Authors

  • Prithvi Raj Arora Department of Aerospace Engineering, Faculty of Engineering, Universiti Putra Malaysia, 43400 UPM,Serdang Selangor Darul Ehsan, Malaysia.
  • Tan Meng Lee Department of Aerospace Engineering, Faculty of Engineering, Universiti Putra Malaysia, 43400 UPM,Serdang Selangor Darul Ehsan, Malaysia.
  • A.M.S. Hamouda A.M.S. Hamouda Department of Mechanical and Manufacturing Bngineering, Faculty of Engineering, Universiti Putra Malaysia, 43400 UPM,Serdang Selangor Darul Ehsan, Malaysia
  • S.M. Sapuan S.M. Sapuan Department of Mechanical and Manufacturing Bngineering, Faculty of Engineering, Universiti Putra Malaysia, 43400 UPM,Serdang Selangor Darul Ehsan, Malaysia.
  • Shah Nor Basri Department of Aerospace Engineering, Faculty of Engineering, Universiti Putra Malaysia, 43400 UPM,Serdang Selangor Darul Ehsan, Malaysia.
  • zairil Azhar Zaludin Department of Aerospace Engineering, Faculty of Engineering, Universiti Putra Malaysia, 43400 UPM,Serdang Selangor Darul Ehsan, Malaysia

Keywords:

finite element. overloading, hole. elastic and plastic stress concentrations, residual stresses, plasticity, stresses at hole edge. model

Abstract

In the present investigation. overloading of 2024-T351 aluminium alloy plate of 6.40 min thick
with 6 min diameter hole has been studied by means of a two-dimensional finite element (FE)
analysis under plane' stress condition. The material for the analysis is assumed to be isotropic,
and von Mises failure criterion with linear isotropic hardening is incorporated. The residual
stress fields around the hole edge have been obtained for an overload range of 33.9% to 99% of the yield stress. Tbe results indicate that there exisls a large amount of compressive tangential residual stress around the hole edge. Reverse yielding was observed for an overlooding CJoL > 75% which is responsible for reducing the extent of compressive residual stresses around the hole edge. The elastic-plastic finite element analysis shows that there is a significant reduction of stress concentration foctor with overloading. A model is also developed giving tangential residual stress at the hole edge for a given overload.

References

Speakman, E. R., 1970. "Fatigue life improvement through stress coining methods", Achievement of High Fatigue Resistance in Metals and Alloys, ASTM STP 467, American Society of Testing and Materials, Philadelphia, Pa., pp 209-227.

Phillips, J. L., 1974, "Sleeve cold working fastener holes" , AFML-TR-74· 10, Vol. I. Air force Materials Laboratory, Wright - Patterson AFB. OH.

Nawwar. A. M. and Shewchuk. J., Dec.1983. "The effect of preload on fatigue strength of residually stressed specimens", Experimental Mechanics, pp 409-41 3.

Smith. P. R. and Shepard, M. J., 2000, "Effect of laser shock processing power density and shot repetition on residual stress distribution and % cold work in Ti·6AI-4V', Proc. 5th National Turbine Engine HCF Conference.

Prevey, P. S., 20m, "The effect of low plasticity burnishing on the HCF performance and FOD resistance of Ti·6AI·4V', Proc. 6111 National Turbine Engine HCF Confere nce, Jack sonvi lle, FL, Mar 5-8.

Damri , D. and Knott, J. F., 1991, "Transient retardations in fatigue crack growth following a single peak overload", Fatigue Fracture Engng. Mater. Strucr. , Vo1.l4. pp 709-719.

Bray, G.H., Reynolds , A. P., and Starke. E. A., Jr., 1992, "Mechanisms of fatigue crack retardation following single tensile overloads in powder metallurgy aluminium alloys", Metall. Trans., Vol. 23A, pp 3055-3066.

Lu, Y. and Li , K., 1993 , "A new model for fatigue crack growth after a single overload" , Engng. Fract. Mech., Vol. 46. pp 849- 856.

Zhang, J. Z., Halli day, M. D., Bowen, P. and Poole, P., 1999, "Three dimensional elastic-plastic fin ite element modelling of small fatigue crack growth under a single tensile overload ', Engng. Fract. Mech., Vol. 63, pp 229-251.

LUSAS (London University Stress Analysis System), 2001, FEA Ltd Forge House , 66 High Street, Kingston upon Thames, Surrey, KT I IHN, United Kingdom.

II . Timoshenko, S. P. and Goodier. J. N., 1982. "Theory of Elasticity ", McGrawHill. pp 15-16.

Kirsch. G., 1898. VDI. Vol. 42.

Heywood, R. 8. , 1952, "Designing by Photoelasticity ", Chapman & Hall, Ltd., London.

Howland. R. 1. C., 1930, Tran sactions of Royal Society (London) , Series A, Vol. 229. pp 49.

Downloads

Published

2018-05-07

How to Cite

Arora, P. R., Meng Lee, T., A.M.S. Hamouda, A. H., S.M. Sapuan, S. S., Basri, S. N., & Zaludin, zairil A. (2018). EFFECT OF SINGLE OVERLOAD ON STRESS DISTRIBUTION IN AN AXIALLY LOADED 2024-T351 ALUMINIUM ALLOY PLATE SPECIMEN WITH A HOLE. Jurnal Mekanikal, 14(2). Retrieved from https://jurnalmekanikal.utm.my/index.php/jurnalmekanikal/article/view/238

Issue

Section

Mechanical

Similar Articles

<< < 5 6 7 8 9 10 11 12 13 14 > >> 

You may also start an advanced similarity search for this article.