FINITE ELEMENT ANALYSIS OF RESIDUAL STRESSES DURING COLD WORKING

Authors

  • Prithvi Raj Arora Division of Aerospace Materials & Structures. Department of Aerospace Engineering, Faculty of Engineering, Universiti Putra Malaysia , 43400 UPM. Serdang, Selangor Darul Ehsan, Malaysia.
  • Jeffrey Tan Meng Lee Division of Aerospace Materials & Structures. Department of Aerospace Engineering, Faculty of Engineering, Universiti Putra Malaysia , 43400 UPM. Serdang, Selangor Darul Ehsan, Malaysia.
  • Christian Barnard Division of Aerospace Materials & Structures. Department of Aerospace Engineering, Faculty of Engineering, Universiti Putra Malaysia , 43400 UPM. Serdang, Selangor Darul Ehsan, Malaysia.
  • Waqar Asrar Division of FluidMechanics & Aerodynamic. Department of Aerospace Engineering, Faculty of Engineering, Universiti PutraMalay sia , 43400 UPM. Scrdang, Selangor Darul Ehsa n, Malaysia.

Keywords:

Cold work. residual stress, elastic-plastic boundary, reverse yielding, finite element analysis. aluminium alloy.

Abstract

A two-dimensional finite dement (FE) analysis. under plane stress condition has been carried out usng 2024-T351 aluminium alloy plate 6.35 mm thick with 6 mm diameter hole subjected to internal pressure. The material for the analysis is assumed to be isotropic, and a von Mises
failure criterion along with linear isotropic hardening is used. The residual stress distribution has
been obtained with pressure loading. The results indicate that large compressive tangential
residual stresses were induced al the hole edge. Reverse yielding was observed for the pressure
loading PI a, > 1.2. A linear relationship has been observed between the applied ND-pressure
and the anticipated equivalent cold work till a ND-pressure of 1.2. A polynominl relationship is
obtained giving the estimate of elastic-plastic boundary for a specified value of ND-pressure at
the hole periphery.

References

Fatigue Technology Inc., 199 1, "Extending the Fatigue of Metal Structures, Materials Testing, FATIGUE TECHNOOLOGY INC.. 150 Andover Park West, Seattle, Washington, USA.

Fatigue Technology Inc., FTI PROCESS SPECIfICATlON 810IC - July 28. 1994, Cold Expansion of Holes Using the Standard Split Sleeve System and Countersink Cold Expansion TM (Cs CXTtm).

Hsu, Y. C. and Forman. R. G., June 1915. "Elastic-plastic analysis of an

infinite sheet having a circular hole under pressure", ASME Journal of Applied Mechanics, pp.347-352.

Budiansky. B., June 1959, "A reassessmcm of deformation theories of plasticity", ASME Journal of Applied Mechanics. pp.259-264.

Mangusan an, O. L., March 1960, "Stresses in the plastic range around a normally loaded circular hole in an infinite sheet". ASME Journal of Appli ed

Mechanics, pp.65-73.

Guo wanlin. 1993, "Elastic-Plastic Analysis of a Finite Sheet with a ColdWorked Hole", Engineering Fracture Mechanics. Vo1.45. xo.e.pp.851-864.

, Budiansky, B., 1971, "An exact solution to an elastic-plastic stress concentration problem", Prikl. Mat. Physics , Vol. 35, ppAO-48.

Arora, P. R. and Simhu. K. R. Y., 1996, "Analytical and experimental evaluation of coldworking process for strain hardening materials", Engine ering Fracture Mechanics, Vol. 53, No.3 . pp.371·385 .

LUSAS (London University Stress Analysis System), 2001, FEA Ltd Forge House, 66 High Street. Kingston upon Thames, Surrey, KT1 1HN, United Kingdom.

MIL-HDBK·5D (McDonnell Douglas Corporation): Military Standardisation Handbook, Metallic Elements for Aerospace Vehicle Structures, 1985. Vols. I & 2. 3.9 1

Timoshenkc. S. P and Goodier. J.N. 1982. Theory oj Elasticity. McGraw Hill

International, 15-16.

Downloads

Published

2018-05-07

How to Cite

Raj Arora, P., Tan Meng Lee, J., Barnard, C., & Asrar, W. (2018). FINITE ELEMENT ANALYSIS OF RESIDUAL STRESSES DURING COLD WORKING. Jurnal Mekanikal, 13(1). Retrieved from https://jurnalmekanikal.utm.my/index.php/jurnalmekanikal/article/view/245

Issue

Section

Mechanical

Similar Articles

<< < 5 6 7 8 9 10 11 12 13 14 > >> 

You may also start an advanced similarity search for this article.